Difference between revisions of "DGC-CLDC0.01 CodeLock Door Controller"

From KONNEKTING Wiki
Jump to navigation Jump to search
 
(3 intermediate revisions by the same user not shown)
Line 8: Line 8:
 
|-
 
|-
 
! Phase
 
! Phase
| Prototype (HW+SW)
+
| Developement Completed
 
|-
 
|-
 
! µC-Board
 
! µC-Board
Line 18: Line 18:
 
! KNX
 
! KNX
 
| [[MicroBCU]]
 
| [[MicroBCU]]
 +
|-
 +
! Manufacturer/Device ID
 +
| 7337 / 20
 +
|-
 +
! Repository
 +
| [https://github.com/SirSydom/konnekting_codelock On GitHub]
 
|}
 
|}
  
Line 31: Line 37:
  
 
== Software ==
 
== Software ==
 +
kdevice.xml: https://github.com/SirSydom/konnekting_codelock/blob/master/software/DGC-CLDC0.01/DGC-CLDC0.01.kdevice.xml
 +
 +
*FW V1.00 (supports Piezo sound transducer) [https://github.com/SirSydom/konnekting_codelock/releases/tag/FW_V01.00 Link]
 +
*FW V1.01 (supports Piezo buzzer) [https://github.com/SirSydom/konnekting_codelock/releases/tag/FW_V01.01 Link]
 +
 +
I plan to update the FW as soon there is a Konnekting Device Library V1.0.0 released, supporting [[FOTB - Firmware Over The Bus]]
  
 
== Hardware ==
 
== Hardware ==
 +
There will no be a Layout or even PVB. The PCB is very simple, you can build it with a bread board (Lochrasterplatine).
 +
Have a look [https://github.com/SirSydom/konnekting_codelock/tree/master/dev_doc here] for help.
  
 
== User Doc ==
 
== User Doc ==
  
 
== Dev Doc ==
 
== Dev Doc ==
 +
See [https://github.com/SirSydom/konnekting_codelock/tree/master/dev_doc GitHub]
  
 
== Build It ==
 
== Build It ==
 +
You need:
 +
 +
*Adafruit ItsyBitsyM0 Arduino-Board
 +
*µBCU
 +
*Keypad with 4x3 Matrix (have a look at AliExpress)
 +
*Piezo-Buzzer
 +
*Hammond 1551KTBU
 +
*some ribbon cable 10 wires 1,27
 +
 +
(not complete, tbd)
  
  

Latest revision as of 08:01, 9 September 2019

Codelock and Doorlock Controller
IMG 20190826 065357703.jpg
Developer SirSydom
Phase Developement Completed
µC-Board ItsyBitsy M0 Express
µC SAMD21G18
KNX MicroBCU
Manufacturer/Device ID 7337 / 20
Repository On GitHub


Short Description

This device is a Codelock with KNX connection which can send KNX telegrams on inserting codes/commands.

It also has some direct outputs to control a automatic lock (Like Abus CFA1000 or similiar).

There is a Keypad for inserting the codes, a piezo speaker for signaling key press and correct/wrong codes, a interface to a Motorlock remote controll (with 3,3V supply).

It fits into a case 40x80x20 (Hammond 1551KTBU) and can be placed in a "Elektronik-Unterputzdose".

Software

kdevice.xml: https://github.com/SirSydom/konnekting_codelock/blob/master/software/DGC-CLDC0.01/DGC-CLDC0.01.kdevice.xml

  • FW V1.00 (supports Piezo sound transducer) Link
  • FW V1.01 (supports Piezo buzzer) Link

I plan to update the FW as soon there is a Konnekting Device Library V1.0.0 released, supporting FOTB - Firmware Over The Bus

Hardware

There will no be a Layout or even PVB. The PCB is very simple, you can build it with a bread board (Lochrasterplatine). Have a look here for help.

User Doc

Dev Doc

See GitHub

Build It

You need:

  • Adafruit ItsyBitsyM0 Arduino-Board
  • µBCU
  • Keypad with 4x3 Matrix (have a look at AliExpress)
  • Piezo-Buzzer
  • Hammond 1551KTBU
  • some ribbon cable 10 wires 1,27

(not complete, tbd)


Links

KNXUF Thread Konnekting Codelock

KNXUF Thread günstiges wasserdichtes Metall-Keypad (~25USD)

KNXUF Thread Abus Hometec CFA / CFB