Difference between revisions of "DFF4.1 Building Instructions"
Jump to navigation
Jump to search
Konnekting (talk | contribs) |
Konnekting (talk | contribs) |
||
| Line 16: | Line 16: | ||
|- | |- | ||
|4 | |4 | ||
| − | |M3 screw | + | |M3 screw, nylon |
|- | |- | ||
|8 | |8 | ||
|relay | |relay | ||
| + | |- | ||
| + | |8 | ||
| + | |screw terminals, cage | ||
|- | |- | ||
|8 | |8 | ||
| Line 69: | Line 72: | ||
|1 | |1 | ||
|PCB enclosure cover, printed and drilled | |PCB enclosure cover, printed and drilled | ||
| + | |- | ||
| + | |1 | ||
| + | |M0dularis+ controller PCB | ||
| + | |- | ||
| + | |1 | ||
| + | |Frontend PCB, 8 Buttons, 8 LEDs | ||
| + | |- | ||
| + | |1 | ||
| + | |1Application PCB, 8x BiRelay | ||
| + | |- | ||
| + | |1 | ||
| + | |MicroBCU with pinheaders | ||
|} | |} | ||
| + | |||
| + | Take the flat cable and cut the following lengths and ensure, each cut part has it's own "red wire": | ||
| + | |||
| + | * xx cm, 6 wires | ||
| + | * xx cm, 8 wires | ||
| + | |||
| + | The result shoud look like this: | ||
| + | |||
| + | INSERT IMAGE HERE | ||
| + | |||
| + | Carefully put the micromatch plugs (2x3 for 6-wire and 2x4 + 2x8 for the 8-wire) onto the cut flat cable as shown here: | ||
| + | |||
| + | INSERT IMAGE HERE | ||
| + | |||
| + | Carefully use a pliers to crimp the plug. Be really careful and take you time. Otherwise you risk damage of micromatch plug! | ||
| + | |||
| + | INSERT IMAGE HERE (pliers + micromatch) | ||
| + | |||
| + | The result should look like this: | ||
| + | |||
| + | INSERT IMAGE HERE | ||
= Controller = | = Controller = | ||
Revision as of 09:16, 6 April 2018
Preparation
Check that all parts are there:
| Pcs. | Part |
|---|---|
| 2 | M3 hex-spacer, nylon, 15mm |
| 2 | M3 hex-spacer, nylon, 18mm |
| 4 | M3 screw, nylon |
| 8 | relay |
| 8 | screw terminals, cage |
| 8 | 3mm LED, green |
| 1 | 3mm LED, red |
| 8 | tactile push button, xx mm |
| 1 | tactile push button, xx mm |
| 1 | DIN Rail enclosure, consisting of:
|
| 1 | MiniUSB socket, vertical |
| 2 | micromatch socket, 2x3 pin |
| 1 | micromatch socket, 2x8 pin |
| 1 | micromatch socket, 2x4 pin |
| 2 | micromatch plug, 2x3 pin |
| 1 | micromatch plug, 2x8 pin |
| 1 | micromatch plug, 2x4 pin |
| 1 | pcs of flat cable |
| 1 | PCB enclosure cover, printed and drilled |
| 1 | M0dularis+ controller PCB |
| 1 | Frontend PCB, 8 Buttons, 8 LEDs |
| 1 | 1Application PCB, 8x BiRelay |
| 1 | MicroBCU with pinheaders |
Take the flat cable and cut the following lengths and ensure, each cut part has it's own "red wire":
- xx cm, 6 wires
- xx cm, 8 wires
The result shoud look like this:
INSERT IMAGE HERE
Carefully put the micromatch plugs (2x3 for 6-wire and 2x4 + 2x8 for the 8-wire) onto the cut flat cable as shown here:
INSERT IMAGE HERE
Carefully use a pliers to crimp the plug. Be really careful and take you time. Otherwise you risk damage of micromatch plug!
INSERT IMAGE HERE (pliers + micromatch)
The result should look like this:
INSERT IMAGE HERE