Difference between revisions of "16CH Binary Input"

From KONNEKTING Wiki
Jump to navigation Jump to search
Line 108: Line 108:
 
  Die Dezimalwerte kann man in die Suite eingeben, beim parameterisieren werden diese Werte ins EEPROM geschrieben. Bei jedem Start werden die Daten ins RAM geladen und decodiert.
 
  Die Dezimalwerte kann man in die Suite eingeben, beim parameterisieren werden diese Werte ins EEPROM geschrieben. Bei jedem Start werden die Daten ins RAM geladen und decodiert.
 
  Aktuell können so 5 "Zimmer" definiert werden
 
  Aktuell können so 5 "Zimmer" definiert werden
  [[File:16CH Binary Input Suite ZimmerErkennung.PNG]]
+
  [[File:16CH Binary Input Suite ZimmerErkennung.PNG|600px]]
  
 
=== HW Documentation ===
 
=== HW Documentation ===

Revision as of 22:22, 1 March 2018

16CH Binary Input
16CH Binary Input Overview.jpg
16CH Binary Input comp.jpg
Developer Matthias F.
Status Version 1.0 finished
Microcontroller/Board
KNX connectivity Mini-BCU


Description

16ch Binary Input (potential-free)

The binary input has 16 inputs available and is used to connect eight conventional push-buttons or floating contacts such as window or relay contacts. There is one status LED for each input. In addition, the input status is sent to the bus. A separate power supply is not necessary


Technical Data:

  • Operating voltage:         KNX Bus voltage <10mA
  • Installation type:             Top Hat Rail mounting
  • Number of Inputs:           16
  • Number of S0-Inputs:      4 (CH13 - CH16)
  • Input polling:                    with 100ms, 300ms or 500ms
  • Typ of Inputs:                   potential-free / floating contacts
  • Max. cable length:           30m tested (more possible)
  • input voltage:                  5V
  • Max. input voltage:          24V (absolute rating, for <1min)
  • Max. input current:          10mA
  • The device makes a contact supply voltage (5V) which is not electrically isolated from the bus voltage!
  • x-Inputs can configure to a "room" ("room"-GA can show if one of the windows is open in the room)

Schematic

16CH Binary Input Schematic.png


Hardware

What you need

for this device do you need:

  • 1x OKW Housing
  • 1x PCB Kit
  • 1x Mounting Kit (screws, ...)
OKW Housing link OKW-Website:[1]
1x B6503121 RAILTEC B, 4 Module
3x B6607140 Klemmenabdeckung, flach 
1x B6607145 Abdeckung KNX, flach
4x B6607142 Klemmenabdeckung, flach 
(1x) B6603180 Frontplatte, 4 Module (only if you don't use the "LED-Status-PCB" 


PCB Kit:
1) Application PCB
2) Controller PCB
3) LED-Status PCB (for function not necessary, only to show the status of the Inputs)
4) Mini-BCU (KNX-Transceiver)
16CH Binary Input PCBs.jpg


Mounting Kit
1x Micromatch cable
8x Screws 


without housing

Software

What you need

  • Arduino IDE (link)
  • Arduino Code for 16CH Binary Input
  • XML-File for 16CH Binary Input
  • KONNEKTING SUITE (link)


Arduino Code

XML-File

User Documentation

SW Documentation

Sperrobjekte

Room classification

Die Raumerkennung funktioniert als 16Bit Wert und jedes Bit ist ein Input. Möchte man also alle 16 Inputs zusammen als "Zimmer" definieren, dann wäre das:
b1111111111111111 = 65535
oder frei, Inputs wären hier: 1,5,6,10,14,15
b1000110001000110 = 35910
Die Dezimalwerte kann man in die Suite eingeben, beim parameterisieren werden diese Werte ins EEPROM geschrieben. Bei jedem Start werden die Daten ins RAM geladen und decodiert.
Aktuell können so 5 "Zimmer" definiert werden
16CH Binary Input Suite ZimmerErkennung.PNG

HW Documentation

Circuit diagram

One VCC Output-Pin shares two Input-Channels. Because of that always two Channels will monitoring together.

S0 interface Up to four Inputs can configure to an S0-interface. possible CH are Ch13 - Ch16 note: If you configure only one Ch to an S0-Interface on an VCC-Output pair, then the output of the other CH can not be switched off, because the VCC-Output voltage supply always both Channels.


16Ch Input
12Ch Input + 4Ch S0-Interface

Developer Documentation

State Machine

START -> Loop over all Channels (activation Outputs x + y -> readout inputs x + y -> update Status LED -> deactivation Outputs x + y)

Build It

Links