Difference between revisions of "DGC-CLDC0.01 CodeLock Door Controller"

Latest revision as of 08:01, 9 September 2019

Codelock and Doorlock Controller

Developer	SirSydom
Phase	Developement Completed
µC-Board	ItsyBitsy M0 Express
µC	SAMD21G18
KNX	MicroBCU
Manufacturer/Device ID	7337 / 20
Repository	On GitHub

Short Description

This device is a Codelock with KNX connection which can send KNX telegrams on inserting codes/commands.

It also has some direct outputs to control a automatic lock (Like Abus CFA1000 or similiar).

There is a Keypad for inserting the codes, a piezo speaker for signaling key press and correct/wrong codes, a interface to a Motorlock remote controll (with 3,3V supply).

It fits into a case 40x80x20 (Hammond 1551KTBU) and can be placed in a "Elektronik-Unterputzdose".

Software

kdevice.xml: https://github.com/SirSydom/konnekting_codelock/blob/master/software/DGC-CLDC0.01/DGC-CLDC0.01.kdevice.xml

FW V1.00 (supports Piezo sound transducer) Link
FW V1.01 (supports Piezo buzzer) Link

I plan to update the FW as soon there is a Konnekting Device Library V1.0.0 released, supporting FOTB - Firmware Over The Bus

Hardware

There will no be a Layout or even PVB. The PCB is very simple, you can build it with a bread board (Lochrasterplatine). Have a look here for help.

User Doc

Dev Doc

See GitHub

Build It

You need:

Adafruit ItsyBitsyM0 Arduino-Board
µBCU
Keypad with 4x3 Matrix (have a look at AliExpress)
Piezo-Buzzer
Hammond 1551KTBU
some ribbon cable 10 wires 1,27

(not complete, tbd)

Links

KNXUF Thread Konnekting Codelock

KNXUF Thread günstiges wasserdichtes Metall-Keypad (~25USD)

KNXUF Thread Abus Hometec CFA / CFB

@@ Line 2: / Line 2: @@
 ! colspan="2"|Codelock and Doorlock Controller
 |-
-! colspan="2"|
+! colspan="2"|[[File:IMG 20190826 065357703.jpg|300px|thumb|center]]
 |-
 ! Developer
@@ Line 8: / Line 8: @@
 |-
 ! Phase
-| Early Developement (HW and SW prototype)
+| Developement Completed
 |-
 ! µC-Board
-| Arduino Pro Mini
+| [https://wiki.konnekting.de/index.php/Recommended_Arduino_Boards#Adafruit_ItsyBitsy_M0_Express ItsyBitsy M0 Express]
 |-
 ! µC
-| atmega328p
+| SAMD21G18
 |-
 ! KNX
-| SiemensBCU / MiniBCU / [MicroBCU]
+| [[MicroBCU]]
+|-
+! Manufacturer/Device ID
+| 7337 / 20
+|-
+! Repository
+| [https://github.com/SirSydom/konnekting_codelock On GitHub]
 |}
 == Short Description ==
-This device will be a Codelock with KNX connection which can send KNX telegrams on inserting codes/commands.
+This device is a Codelock with KNX connection which can send KNX telegrams on inserting codes/commands.
+It also has some direct outputs to control a automatic lock (Like Abus CFA1000 or similiar).
+There is a Keypad for inserting the codes, a piezo speaker for signaling key press and correct/wrong codes, a interface to a Motorlock remote controll (with 3,3V supply).
-It also will have some direct outputs to control a automatic lock.
+It fits into a case 40x80x20 (Hammond 1551KTBU) and can be placed in a "Elektronik-Unterputzdose".
 == Software ==
+kdevice.xml: https://github.com/SirSydom/konnekting_codelock/blob/master/software/DGC-CLDC0.01/DGC-CLDC0.01.kdevice.xml
+*FW V1.00 (supports Piezo sound transducer) [https://github.com/SirSydom/konnekting_codelock/releases/tag/FW_V01.00 Link]
+*FW V1.01 (supports Piezo buzzer) [https://github.com/SirSydom/konnekting_codelock/releases/tag/FW_V01.01 Link]
+I plan to update the FW as soon there is a Konnekting Device Library V1.0.0 released, supporting [[FOTB - Firmware Over The Bus]]
 == Hardware ==
+There will no be a Layout or even PVB. The PCB is very simple, you can build it with a bread board (Lochrasterplatine).
+Have a look [https://github.com/SirSydom/konnekting_codelock/tree/master/dev_doc here] for help.
 == User Doc ==
 == Dev Doc ==
+See [https://github.com/SirSydom/konnekting_codelock/tree/master/dev_doc GitHub]
 == Build It ==
+You need:
+*Adafruit ItsyBitsyM0 Arduino-Board
+*µBCU
+*Keypad with 4x3 Matrix (have a look at AliExpress)
+*Piezo-Buzzer
+*Hammond 1551KTBU
+*some ribbon cable 10 wires 1,27
+(not complete, tbd)